Print
2025 №06 (08) DOI of Article
10.37434/as2025.06.01 		2025 №06 (02)

Automatic Welding 2025 №06


"Avtomatychne Zvaryuvannya" (Automatic Welding), #6, 2024, pp. 3-9

Formation of coatings containing Ti3AlC2 max phase by deposition of TiC-TiAl powder by plasma and high-velocity oxy-fuel spraying methods

N.V. Vihilianska1, T.V. Tsymbalista1, P.P. Grishchenko1, A.P. Murashov1, O.Y. Gudymenko2

1E.O. Paton Electric Welding Institute of the NAS of Ukraine 11 Kazymyr Malevych Str., 03150, Kyiv, Ukraine. Е-mail: pewinataliya@gmail.com
2V. Lashkaryov Institute of Semiconductor Physics of the NAS of Ukraine. 45 Nauky Ave., 03028, Kyiv, Ukraine. E-mail: gudymen@ukr.net

The work investigated the formation of coatings containing the MAX phase Ti3AlC2 by plasma and high-velocity oxy-fuel spraying using TiC-TiAl powder. The composite powder was produced by processing a powder mixture of the initial components TiAl and TiC in a planetary mill for 5 h, resulting in the formation of a powder with conglomerate-type particles containing the phases of the initial components and the target MAX phase Ti3AlC2. Coatings produced by plasma and high-velocity oxy-fuel spraying methods were investigated using X-ray phase analysis, optical microscopy and microdurometry. It was found that during plasma spraying, due to the intensive interaction of powder particles with the gas environment and high-temperature process conditions, the formation of titanium carbonitride TiC0.2N0.8 and a significant decrease in the content of the MAX phase Ti3AlC2 relative to the powder are observed in the coating. The coatings have a lamellar structure with high (~ 15 %) porosity and microhardness of 4390 ± 920 MPa. At high-velocity oxy-fuel spraying, due to the lower thermal load compared to the plasma spraying method, the coating retains most of the original phase composition of the powder. The coating structure is less lamellar and denser (porosity does not exceed 1 %), contains unmelted and partially melted deformed particles, and the average microhardness is 3810 ± 840 MPa. 23 Ref., 3 Tabl., 5 Fig.
Keywords: coating, plasma spraying, high-velocity oxy-fuel spraying, MAX phase, phase composition, structure, microhardness


Received: 07.08.2025
Received in revised form: 07.11.2025
Accepted: 10.12.2025

References

1. Dahlqvist, M., Barsoum, M. W., Rosen J. (2024) MAX phases – Past, present, and future. Materials Today, 72, 1–24. DOI: https://doi.org/10.1016/j.mattod.2023.11.010
2. Radovic, M., Barsoum, M. W. (2013) MAX phases: Bridging the gap between metals and ceramics. American Ceramic Society Bulletin, 92(3), 20–27.
3. Li, X., Xie, X., Gonzalez-Julian, J., Malzbender, J., Yang, R. (2020) Mechanical and oxidation behavior of textured Ti2AlC and Ti3AlC2 MAX phase materials. J. of the European Ceramic Society, 40(15), 5258–5271. DOI: https://doi.org/10.1016/j.jeurceramsoc.2020.07.043
4. Li, X., Zheng, L., Qian, Y., Xu, J., Li, M. (2017) Effects of high temperature oxidation on mechanical properties of Ti3AlC2. J. Mater. Sci. Technol. 33(6), 596–602. DOI: 10.1016/j.jmst.2016.05.004.
5. Wei, L., Liu, J., Wu, X. et al. (2019) In situ fabrication of Ti–Al/Ti2AlC composite by hot-press sintering. J. of Alloys and Compounds, 813, 52220. DOI: https://doi.org/10.1016/j.jallcom.2019.152200
6. Wang, P., Bingchu, M., Xiaolin H. et al. (2007) Fabrication of Ti2AlC by spark plasma sintering from elemental powders and thermodynamics analysis of Ti-Al-C system. J. of wuhan university of technology-Mater. Sci. Ed., 22(2), 325–328. DOI: https://doi.org/10.1007/s11595-006-2325-x.
7. Xie X., Yang R., Cui Y. et al. (2020) Fabrication of textured Ti2AlC lamellar composites with improved mechanical properties. J. of Material Science and Technology, 38, 86–92. DOI: https://doi.org/10.1016/j.jmst.2019.05.070
8. Sadeghi, E., Karimzadeh, F., Abbasi, M.H. (2013) Thermodynamic analysis of Ti–Al–C intermetallics formation by mechanical alloying. J. of Alloys and Compounds, 576, 317–323. DOI: https://doi.org/10.1016/j.jallcom.2013.05.196
9. Edrisi, A., Aghajani, H., Seyedein, S.H. et al. (2024) Synthesis of high purity Ti2AlC MAX phase by combustion method through thermal explosion mode: Optimization of process parameters and evaluation of microstructure. Ceramics International [Preprint]. DOI: https://doi.org/10.1016/j.ceramint.2024.09.431
10. Eklund, P., Beckers, M., Jansson, U. et al. (2010) The Mn+1AXn phases: Materials science and thin-film processing. Thin Solid Films, 518(8), 1851–1878. DOI: https://doi. org/10.1016/j.tsf.2009.07.184
11. Vihilianska, N.V., Filonenko, D.V., Yushchenko, A.O., Senderowski, C., Grivel, J.-C. (2024) Thermal spraying of coatings, containing Cr2AlC max-phase (Review). Avtomatychne Zvaryuvannya, 1, 51–59. DOI: https://doi.org/10.37434/as2024.01.06
12. Vihilianska, N., Yantsevich, K., Olevska, L. et al. (2024) Formation of coatings based on MAX phase Ti3SiC2 under gas-thermal deposition methods (Review). Visnyk KrNU imeni Mykhaila Ostrohradskoho, 4 (147), 135–142.
13. Frodelius, J., Sonestedt, M., Björklund, S., et al. (2008) Ti2AlC coatings deposited by High Velocity Oxy-Fuel spraying. Surface and coatings technology, 202(24), 5976–5981. DOI: https://doi.org/10.1016/j.surfcoat.2008.06.184
14. Sonestedt, M., Frodelius, J., Palmquist, J.-P. et al. (2010) Microstructure of high velocity oxy-fuel sprayed Ti2AlC coatings. J. of Materials Science, 45(10), 2760–2769. DOI: https://doi.org/10.1007/s10853-010-4263-4
15. Zhang, Z., Lim, S. H., Chai, J. et al. (2017) Plasma spray of Ti2AlC MAX phase powders: Effects of process parameters on coatings properties. Surface and coatings technology, 325, 429–436. DOI: https://doi.org/10.1016/j.surfcoat. 2017.07.006
16. Yu, H., Suo, X., Gong, Y. et al. (2016) Ti3AlC2 coatings deposited by liquid plasma spraying. Surface and coatings technology, 299, 123–128. DOI: https://doi.org/10.1016/j.surfcoat.2016.04.076
17. He, W., Li, J., Liu, K. (2024) Ti3AlC2-modified NiCrAlY as a metallic bond coat for thermal barrier coatings: a study on high-temperature oxidation resistance. J. of physics: conference series, 2808, 012009. DOI: https://doi.org/10.1088/1742-6596/2808/1/012009
18. Huang, J., Chen, W., Lü, K.et al. (2024) Self-healing and thermal stability of LaMgAl11O19-Ti3AlC2 composites for high-temperature abradable applications. Coatings, 14(8), 938. DOI: https://doi.org/10.3390/coatings14080938
19. Li, Q., Yuan, X., Xu, H. (2019) Microstructure and fracture toughness of in-situ nanocomposite coating by thermal spraying of Ti3AlC2/Cu powder. Ceramics International, 45(10), 13119–13126. DOI: https://doi.org/10.1016/j.ceramint.2019.03.246
20. Matthews, A., Leyland, S. (1995) ASM Engineered Materials Reference Book. Second Edition. Michael Bauccio (Ed.). ASM International, Materials Park, OH, 1994 Hard Coatings for Tribological Applications. Surface and Coatings Technology, 71, 71–78.
21. Cui, N., Wu, Q., Yan, Z., Zhou, H., Wang, X. (2019) The microstructural evolution, tensile properties, and phase hardness of a TiAl alloy with a high content of the β Phase. Materials, 12(17), 2757. DOI: https://doi.org/10.3390/ma12172757
22. Li, K., Wang, X., Chen, H., Huang, X., Zhu, G., Tu, G. (2023) Fabrication of Ti3Al-based intermetallic alloy by laser powder bed fusion using a powder mixture. Materials, 16(7), 2699. DOI: https://doi.org/10.3390/ma16072699
23. Wang, X.H., Zhou, Y.C. (2010) Layered machinable and electrically conductive Ti2AlC and Ti3AlC2 ceramics: a review. J. of materials science and technology, 26(5), 385–416. DOI: https://doi.org/10.1016/s1005-0302(10)60064-3

Advertising in this issue: