Print

2022 №08 (02) DOI of Article
10.37434/tpwj2022.08.03
2022 №08 (04)

The Paton Welding Journal 2022 #08
The Paton Welding Journal, 2022, #8, 18-24 pages

Influence of the composition of charge components of flux-cored strips of C–Fe–Cr–Nb alloying system on chemical composition and structure of the deposited metal

O.P. Voronchuk, O.P. Zhudra, T.V. Kaida, O.V. Petrov, L.M. Kapitanchuk, I.L. Bogaichuk


E.O. Paton Electric Welding Institute of the NASU. 11 Kazymyr Malevych Str., 03150, Kyiv, Ukraine. E-mail: voronchuk@aranei.com

Abstract
It is common knowledge that wear resistance of the deposited chromium carbide layer, additionally alloyed by such carbide- forming elements, as molybdenum, niobium, etc., largely depends on the reinforcing phase characteristics, its concentration, and qualities of matrix alloy. Good performance of such alloys under the conditions of abrasive wear at up to 600 оС temperature, is achieved by adding niobium to the alloy composition. This work is a study of charge components of flux-cored strips of С–Fe–Cr–Nb alloying system on the deposited metal composition and properties. The methods of X-ray structural, metallographic and X-ray microprobe analysis of metal of 500Kh22B7 type deposited by flux-cored strips, revealed the dependence of concentrations, form, orientation, phase components and integral hardness of the deposited layer on the type of addition of the main carbide-forming element, namely chromium, to the charge and flux-cored strip cross-section. It was found that at addition of chromium carbide Cr3C2 to the flux-cored strip charge, carbide phase concentration in the deposited layer increases by 10 %. Complex carbides of (CrFe)7С3 system are predominatly present in the deposited metal for all the samples. Niobium forms individual carbide components of much smaller dimensions, compared to chromium carbide components. Optimal concentration of the carbide phase in the metal of 500Kh22B7 type deposited by flux-cored strip is achieved by addition of a carbide-forming element, namely chromium, to the electrode material charge, in the form of chromium carbide and ferrochromium. Flux-cored strip cross-section and surfacing modes practically do not affect the deposited layer properties. 11 Ref., 8 Tabl., 4 Fig.
Keywords: flux-cored strip, chromium carbide, ferrochromium, niobium, carbides, hardness, microstructure, matrix, concentration

Received: 14.06.2022
Accepted: 17.10.2022

References

1. Ryabtsev, I.A., Senchenkov, I.K., Turyk, E.V. (2015) Surfacing. Materials, technologies, mathematical modeling. Gliwice, Wydawnictwo Politechniki Śląskiej. https://doi.org/10.15407/tpwj2015.06.29
2. Ryabtsev, I.A. (2005) High-efficiency wide-layer surfacing using electrode wires and strips. The Paton Welding J., 6, 36-41.
3. Pokhodnya, I.K., Shlepakov, V.N., Maksimov, S.Yu., Ryabtsev, I.A. (2010) Research and developments of the E.O.Paton Electric Welding Institute in the field of electric arc welding and surfacing using flux-cored wire (Review). The Paton Welding J., 12, 34-42.
4. Voronchuk, A.P., Zhudra, A.P., Petrov, A.V., Kochura, V.O. (1991) Influence of temperature on hardness and heat resistance of high-chromium cast irons deposited by fluxcored strips. Avtomatich. Svarka, 6, 44-50 [in Russian]. https://doi.org/10.15407/as2019.06.07
5. Zhudra, A.P., Voronchuk, A.P. (2012) Cladding flux-cored strips (Review). The Paton Welding J., 1, 34-38.
6. Kuskov, Yu.M., Bogajchuk, I.L., Chernyak, Ya.P., Evdokimov, A.I. (2013) Electroslag surfacing of parts, made of high-chrome cast iron, using cast iron shot. The Paton Welding J., 8, 47-49.
7. Kuskov, Yu.M., Evdokimov, A.I. (2014) Electroslag surfacing of wear-resistant alloyed cast irons. Uprochniayushchie Tekhnologii i Pokrytiya, 10, 21-24 [in Russian].
8. Livshits, L.S., Grinberg, N.A., Kurkumelli, E.G. (1969) Fundamentals of alloying of deposited metal. Moscow, Mashinostroenie [in Russian].
9. Kudinov, V.D., Filimonov, B.V., Shevnov, S.A., Netesa, I.V. (1985) Cladding by composite alloys of metallurgical equipment parts. Avtomatich. Svarka, 5, 48-50 [in Russian].
10. Voronchuk, A.P. (2009) Effect of concentration of hard particles on gas-abrasive wear resistance of composite alloy. The Paton Welding J., 8, 43-44.
11. Zhudra, A.P., Voronchuk, A.P., Petrov, A.V., Kochura, V.O. (2012) Technology, equipment and materials for manufacturing of sheet lining elements. Svarochn. Proizvodstvo, 11, 40-43 [in Russian].

Suggested Citation

O.P. Voronchuk, O.P. Zhudra, T.V. Kaida, O.V. Petrov, L.M. Kapitanchuk, I.L. Bogaichuk (2022) Influence of the composition of charge components of flux-cored strips of C–Fe–Cr–Nb alloying system on chemical composition and structure of the deposited metal. The Paton Welding J., 08, 18-24.