Print

2022 №10 (04) DOI of Article
10.37434/tpwj2022.10.05
2022 №10 (06)

The Paton Welding Journal 2022 #10
The Paton Welding Journal, 2022, #10, 30-36 pages

Higher current harmonics in transformer power sources with pulsed devices of welding arc stabilization

A.M. Zhernosekov1, O.A. Andrianov2, S.V. Rymar1, O.F. Shatan1, A.O. Mukha1


1E.O. Paton Electric Welding Institute of the NASU. 11 Kazymyr Malevych Str., 03150, Kyiv, Ukraine. E-mail: zhernosekov@paton.kiev.ua
2Ukrainian National Committee of International Chamber of Commerce (ICC Ukraine). 19B, Reitarska St. 01034, Kyiv. E-mail: office@iccuq.org

Abstract
Transformer power sources of welding arc of industrial frequency alternating current generate into the mains the level of higher current harmonics, which is by an order of magnitude lower by the value of the coefficient of general harmonic distortion, than that of the inverter power sources. Here, their high electromagnetic compatibility with other equipment of the mains is achieved. Moreover, they are much easier to maintain and more reliable. Harmonic composition of current during a.c. welding was calculated at application of pulsed devices of arc stabilization. It is shown that application of stabilizing pulses with the polarity opposite to that of arc current, is more advantageous that the use of pulses with the polarity coinciding with that of arc current. Advantages as to welding process effectiveness and smaller generation of higher current harmonics are also observed. 18 Ref., 7 Fig.
Keywords: welding power sources, transformers, welding arc, stabilizing pulses, higher current harmonics

Received: 10.07.2022
Accepted: 01.12.2022

References

1. Zaruba, I.I., Andreev, V.V., Dymenko, V.V. (2001) Improvement of transformers for manual arc welding. The Paton Welding J., 3, 43-46.
2. Kiji, N., Kobayashi, K., Ishii, J., Yamaoka, H. (2003) Development of high efficiency arc welding methods. The Paton Welding J., 10–11, 56-60.
3. Andrianov, A.A., Sidorets, V.N. (2009) Optimization of modes for stabilization of alternating-current welding arc. Elektrotekhnika i Elektromechanika, 2, 5–12 [in Ukrainian].
4. Paton, B.E., Zaruba, I.I., Dymenko, V.V., Dymenko, V.V., Shatan, A.F. (2006) Lowering of material content of power sources and power consumption in welding. The Paton Welding J., 10, 15-23.
5. Paton, B.E., Zaruba, I.I., Dymenko, V.V., Dymenko, V.V., Shatan, A.F. (2007) Welding power sources with pulse stabilization of arc burning. Kyiv, Ekotekhnologiya [in Russian].
6. Andrianov, O.A. (2010) Optimization of welding stabilization process of corrosion-resistant steels by alternating current. In: Syn of Thesis for Cand. of Tech. Sci. Degree. Kyiv, NTUU KPI [in Ukrainian].
7. Rymar, S.V., Zhernosekov, A.M., Sidorets, V.N. (2011) Effect of single-phase power sources of welding arc on electric mains. The Paton Welding J., 12, 7-12.
8. Rymar, S.V., Zhernosekov, A.M., Sydorets, V.N. (2011) Influence of welding power sources on three-phase mains. The Paton Welding J., 10, 40-45.
9. Pentegov, I.V., Latansky, V.P., Sklifos, V.V. (1992) Smallsized power sources with improved power indices. Kyiv, PWI, 66–71 [in Russian].
10. Zaruba, I.I., Dymenko, V.V., Kukharsky, V.Ya. (1991) Application of multioperator alternating-current power sources for arc welding. Avtomatich. Svarka, 2, 59–63 [in Russian].
11. Pentegov, I.V., Dymenko, V.V. Sklifos, V.V. (1994) Welding power sources with pulse arc ignition. Avtomatich. Svarka, 7–8, 36–39 [in Russian].
12. Sidorets, V.N., Andrianov, A.A. (2007) Methods of analysis of stabilization modes of alternating-current welding arc. Tekhnichna Elektrodynamika. Sylova Elektronika ta Energoefektyvnist, 5, 71–74 [in Russian].
13. Paice, D.A. (1995) Power Electronic Converter Harmonics. Multipulse Methods for Clean Power. NY, IEEE PRESS.
14. Sidorets, V.N., Kunkin, D.D., Moskovith, G.N. (2011) Harmonic analysis of alternating current of electric welding arc. Tekhnichna Elektrodynamika. Sylova Elektronika ta Energoefektyvnist, 1, 219–222, [in Russian].
15. Pentegov, I.V., Sidorets, V.N. (1988) Energy parameters in mathematical model of dynamic welding arc. Avtomatich. Svarka, 11, 36–40 [in Russian].
16. Sidorets, V.N., Pentegov, I.V. (2013) Deterministic chaos in nonlinear circuits with electric arc. Kyiv, IAW [in Russian].
17. Sidorets, V.N. (2006) Method of multiple shooting for the study of bifurcations of dynamical systems. Elektronnoe Modelirovanie, 4 (28), 3–13 [in Russian].
18. Shatan, A.F., Andrianov, A.A., Sidorets, V.N., Zhernosekov, A.M. (2009) Efficiency of stabilisation of the alternating-current arc in covered-electrode welding. The Paton Welding J., 3, 21-23.

Suggested Citation

A.M. Zhernosekov, O.A. Andrianov, S.V. Rymar, O.F. Shatan, A.O. Mukha (2022) Higher current harmonics in transformer power sources with pulsed devices of welding arc stabilization. The Paton Welding J., 10, 30-36.