The Paton Welding Journal, 2026, №09

2026 №09 (06)

DOI of Article 10.37434/tpwj2026.09.07

2026 №09 (08)

---

The Paton Welding Journal, 2026, #9, 64-73 pages

Influence of arc 3D printing parameters on the mechanical properties of Inconel 625 deposit

S.I. Motrunich¹, O.V. Yarovytsyn¹, I.R. Volosatov¹, D.S. Tomko², Ji Junwen^2,3

¹E.O. Paton Electric Welding Institute of the NASU. 11 Kazymyr Malevych Str., 03150, Kyiv, Ukraine. E-mail: motrunich@nas.gov.ua
²National Technical University of Ukraine “Igor Sikorsky Kyiv Polytechnic Institute” 37 Prosp. Beresteiskyi, 03056, Kyiv, Ukraine
³Technical University of Munich 21 Arcisstrasse, Munich, Bavaria, 80333, Germany

Abstract
The influence of wire arc additive manufacturing (WAAM) process parameters using a consumable wire electrode in shielding gas environment on the mechanical properties of a multilayer nickel-based superalloy Inconel 625 deposit in the as-built condition in the temperature range of 20–1100 °C was investigated. Full-size cylindrical specimens of 5×M10 diameter at 20 °C and miniature flat proportional specimens with a working part cross-section of 2.5×2.5 mm at 20–1100 °C were manufactured and tested from a fabricated wall-type vertical structure. Results of metallographic examinations performed by scanning electron microscopy are presented, showing the features of columnar dendritic structure and morphology of secondary phases in different zones of the fabricated component. The deformability of the produced Inconel 625 deposit is analyzed from the viewpoint of the known increased resistance of the alloy to two subtypes of hot cracks by the solid-state cracking mechanism. It is shown that the transition from Ar shielding gas to a mixture of 97.5 % Ar + 2.5 % CO2 when using WAAM process in the temperature range of 600–900 °C significantly reduces the ultimate tensile strength, yield strength, and ductility values for the produced Inconel 625 deposit, particularly at a temperature of 800 °C — approximately by 1.5 times. For Inconel 625 alloy, a comparison of experimental data on ultimate tensile strength for the WAAM-deposited metal and corresponding published data for industrial conventionally manufactured semi-finished products was made.
Keywords: wire arc additive manufacturing, WAAM process, Inconel 625 alloy, deposit, microstructure, short-term mechanical properties, elevated temperatures

Received: 13.10.2026
Received in revised form: 12.05.2026
Accepted: 24.09.2026

References

1. Amiri, V., Naffakh-Moosavy, H. (2024) Wire arc additive manufacturing of functionally graded carbon steel - stainless steel 316L - Inconel 625: Microstructural characterization and mechanical behavior. J. of Advanced Joining Processes, 9, 100194. https://doi.org/10.1016/j.jajp.2024.100194
2. Mohanraj, R., Abdul Basith, S.N., Chandru, S. et al. (2024) A review on microstructure and mechanical properties of Inconel 625 alloy fabricated using wire arc additive manufacturing process. Rapid Prototyping J., 30(7), 1337-1347. https://doi.org/10.1108/RPJ-11-2023-0387
3. Gurmesa, F.D., Lemu, H.G., Tucho, W.M., Muleta, B.B. (2025) Impacts of wire diameter on microstructure and hardness of Inconel 625 fabricated by wire arc additive manufacturing. J. of Materials Research and Technology, 37, 5423-5435. https://doi.org/10.1016/j.jmrt.2025.07.175
4. Markanday, J.F.S. (2022) Applications of alloy design to cracking resistance of additively manufactured Ni-based alloys. Mater. Sci. and Technol., 38(16), 1300-1314. https://doi.org/10.1080/02670836.2022.2068759
5. Ghoussoub, J.N., Tang, Y.T., Dick-Cleland, W.J.B. et al. (2022) On the influence of alloy composition on the additive manufacturability of Ni-based superalloys. Metallurgical and Materials Transact. A, 53A, 962-983. https://doi.org/10.1007/s11661-021-06568-z
6. Wei, Q., Xie, Y., Teng, Q. et al. (2022) Crack types, mechanisms, and suppression methods during high-energy beam additive manufacturing of nickel-based superalloys: A review. Chinese J. of Mech. Eng.: Additive Manufacturing Frontiers, 1(4), 100055. https://doi.org/10.1016/j.cjmeam.2022.100055
7. Rodrigues, T.A., Cipriano Farias, F.W., Avila, J.A. et al. (2023) Effect of heat treatments on Inconel 625 fabricated by wire and arc additive manufacturing: An in situ synchrotron X-ray diffraction analysis. Sci. and Technol. of Welding and Joining, 28(7), 534-539. https://doi.org/10.1080/13621718.2023.2187927
8. Singh, J.B. (2022) Alloy 625. Microstructure, Properties and Performance. Singapore, Springer Nature Singapore Pte Ltd. https://doi.org/10.1007/978-981-19-1562-8
9. Saravanakumar, K., Balaji, V.G., Srijha, T. et al. (2024) Analysis of microstructure and mechanical properties of Inconel 625 alloy by wire arc additive manufacturing (WAAM). Archives of Metallurgy and Materials, 69(3), 1079-1086. https://doi.org/10.24425/amm.2024.150928
10. Pratheesh Kumar, S., Elangovan, S., Mohanraj, R., Ramakrishna, J.R. (2021) A review on properties of Inconel 625 and Inconel 718 fabricated using direct energy deposition. Materials Today: Proceedings, 46(17), 7892-7906. https://doi.org/10.1016/j.matpr.2021.02.566
11. Madesh, R., Gokul Kumar, K. (2023) Multi-layer additive manufacturing on nickel-based superalloy by optimization of pulsed mode process parameters of single-layer bead geometry. Materials Today Communications, 37, 107463. https://doi.org/10.1016/j.mtcomm.2023.107463
12. Ravi, G., Murugan, N., Arulmani, R. (2020) Microstructure and mechanical properties of Inconel-625 slab component fabricated by wire arc additive manufacturing. Mater. Sci. and Technol., 36(16), 1785-1795. https://doi.org/10.1080/02670836.2020.1836737
13. Rashid, M., Sabu, S., Kunjachan, A. et al. (2024) Advances in wire-arc additive manufacturing of nickel-based superalloys: Heat sources, DfAM principles, material evaluation, process parameters, defect management, corrosion evaluation and post-processing techniques. Inter. J. of Lightweight Mater. and Manuf., 7(6), 882-913. https://doi.org/10.1016/j.ijlmm.2024.05.009
14. Ajithkumar, S., Arulmurugan, B., Manikandan, M. et al. (2025) Role of shielding gas in tailoring microstructure and anisotropy in wire arc additive manufactured Inconel 686. Scientific Reports, 15, 21192. https://doi.org/10.1038/s41598-025-08197-7
15. DuPont, J.N., Lippold, J.C., Kiser S.D. (2009) Welding metallurgy and weldability of nickel-base alloys. Hoboken, John Wiley & Sons. https://doi.org/10.1002/9780470500262
16. Ji, J., Zavdoveev, A., Vedel, D. et al. (2023) CMT-based wire arc additive manufacturing of Inconel 625 alloy. Emerging Materials Research, 12(3), 315-322. https://doi.org/10.1680/jemmr.23.00053
17. Yushchenko, K.A., Yarovitsyn, A.V., Chervyakov, N.O. et al. (2019) Evaluation of short-term mechanical properties of a joint of difficult-to-weld nickel high-temperature alloys of ZhS6 type. The Paton Welding J., 7, 29-35. https://doi.org/10.15407/tpwj2019.07.07
18. Costa, J.F.M., Jorge, J.C.F., de Souza, L.F.G. et al. (2024) Microstructural evaluation of Inconel 625 weld cladding deposited by the GMAW and GMAW with rotating electrode processes. Tecnologia em Metalurgia Materiais e Mineração, 21, e2848. https://doi.org/10.4322/2176-1523.20242848
19. Yarovytsyn, O., Cherviakov, M., Zviahintseva, H. et al. (2024) On the issue of assessing the probability and preventing the occurrence of «ductility dip cracking» mechanism under conditions of multi-layer welding arc 3D-overlaying process on nickel and cobalt alloys. In: Proc. of the 77th IIW Annual Assembly. Commission IX-H «Behavior of Metals Subjected to Welding», IIW Doc. IX-H-973-2024, 7-12 July 2024, Rhodes, Greece.
20. de Oliveira, M.M., Couto, A.A., Almeida, G.F.C. et al. (2019) Mechanical behavior of Inconel 625 at elevated temperatures. Metals, 9(3), 301-312. https://doi.org/10.3390/met9030301
21. Special Metals Corporation (2013) Inconel® alloy 625. Technical Bulletin. www.specialmetals.com/documents/technical- bulletins/inconel/inconel-alloy-625.pdf

---

Suggested Citation

S.I. Motrunich, O.V. Yarovytsyn, I.R. Volosatov, D.S. Tomko, Ji Junwen (2026) Influence of arc 3D printing parameters on the mechanical properties of Inconel 625 deposit. The Paton Welding J., 09, 64-73. https://doi.org/10.37434/tpwj2026.09.07

---