The Paton Welding Journal, 2024, №12



2024 №12 (04)

DOI of Article 10.37434/tpwj2024.12.05

2024 №12 (06)

---

The Paton Welding Journal, 2024, #12, 30-34 pages

Evaluation of the mechanical characteristics of CFRP composites and modeling of the delamination phenomenon

A. Savin^1,2, R. Steigmann¹, M.D. Stanciu², C.I. Moraras³, G. Dobrescu¹

¹Nondestructive testing Department, National Institute of R&D for Technical Physics, Iasi 15 D. Mangeron Blvd, Iasi 700050, Romania. E-mail: asavin@phys-iasi.ro
²Faculty of Mechanical Engineering, Transilvania University of Brașov 29 Eroilor Blvd., 500036 Brașov, Romania
³Faculty of Mechanical Engineering, Technical University Gh. Asachi Iasi, Romania 45 D. Mangeron Blvd, Iasi 700050, Romania

Abstract
In the category of new and advanced materials, carbon fiber reinforced plastic (CFRP) composite materials are used in areas such as structural materials in aeronautics, transport, etc. The bi-phasic structure of CFRP requires knowledge of both fiber and matrix properties. In the conditions where possible delamination’s occur during use, these depend both on the properties of the interfaces and of the interlaminate. The appropriate ultrasound (US) techniques allow the determination of the propagation speed of the longitudinal and transverse waves which are used in the evaluation of the elastic modulus E, shear modulus G on the three principal directions. C-scan US using phased array allows the emphasizing and characterization of ones with porosities that appear during composite fabrication or due to local overheating. The results are compared with those obtained by a dynamic mechanical analyzer (DMA), being found a good correlation. These procedures allow also the emphasizing of matrix damages due to high temperature used or establishing maximum temperature for used.
Keywords: CFRP, nondestructive testing, ultrasound, DMA

Received: 30.09.2024
Received in revised form: 12.11.2024
Accepted: 25.12.2024

References

1. Tran, P., Wu, C., Saleh, M. et al. (2021) Composite structures subjected to underwater explosive loadings: A comprehensive review. Composite Structures, 263, 113684. https://doi.org/10.1016/j.compstruct.2021.113684
2. Ozkan, D., Gok, MS., Karaoglanli, AC (2020) Carbon fiber reinforced polymer (CFRP) composite materials. Their characteristic properties, industrial application areas and their machinability. Adv. Struct. Mater., 124, 235-253. https://doi.org/10.1007/978-3-030-39062-4_20
3. Mathes, V. (2018) The composites industry: plenty of opportunities in a heterogeneous market. Reinforced Plastics, 62(1), 44-51. https://doi.org/10.1016/j.repl.2017.05.002
4. Zorko, D., Tavčar, J., Bizjak, M. et al. (2021) High cycle fatigue behavior of autoclave-cured woven carbon fiber-reinforced polymer composite gears. Polymer Testing, 102, 107339. https://doi.org/10.1016/j.polymertesting.2021.107339
5. Othman, R., Ismail, NI, Pahmi, MAAH et al. (2018) Application of carbon fiber reinforced plastics in automotive industry: A review. J. Mech. Manuf., 1, 144-154.
6. Kaw, AK (2006) Mechanics of composite materials. 2nd Ed. Taylor and Francis, NY https://doi.org/10.1201/9781420058291
7. Sang, L., Wang, Y., Wang, C. et al. (2019) Moisture diffusion and damage characteristics of carbon fabric reinforced polyamide 6 laminates under hydrothermal aging. Composites, Pt A. Applied Sci. and Manufacturing, 123, 242-252. https://doi.org/10.1016/j.compositesa.2019.05.023
8. Ortiz, JD, Khedmatgozar Dolati, SS, Malla, P. et al. (2023) FRP-reinforced/strengthened concrete: State-of-the-art review on durability and mechanical effects. Materials, 16(5), 1990. https://doi.org/10.3390/ma16051990
9. Hübner, M., Lepke, D., Hardi, E. et al. (2019) Online monitoring of moisture diffusion in carbon fiber composites using miniaturized flexible material integrated sensors. Sensors, 19(8), 1748. https://doi.org/10.3390/s19081748
10. Lei, Y., Kang, Z., Zhang, J. et al. (2022) Effect of freeze-thaw cycling on the mechanical properties of continuous carbon fiber- reinforced polyamide 6 composites. Polymer Testing, 114, 107704. https://doi.org/10.1016/j.polymertesting.2022.107704
11. Romanowicz, M. (2012) A numerical approach for predicting the failure locus of fiber reinforced composites under combined transverse compression and axial tension. Computational Materials Sci., 51(1), 7-12. https://doi.org/10.1016/j.commatsci.2011.07.039
12. Cugnoni, J., Amacher, R., Kohler, S. et al. (2018) Towards aerospace grade thin-ply composites: Effect of ply thickness, fiber, matrix and interlayer toughening on strength and damage tolerance. Composites Sci. and Technology, 168, 467-477. https://doi.org/10.1016/j.compscitech.2018.08.037
13. Van de Werken, N., Tekinalp, H., Khanbolouki, P. et al. (2020) Additively manufactured carbon fiber-reinforced composites: State of the art and perspective. Additive Manufacturing, 31, 100962. https://doi.org/10.1016/j.addma.2019.100962
14. Bhatt, AT, Gohil, PP, Chaudhary, V. (2018) Primary manufacturing processes for fiber reinforced composites: history, development & future research trends. In: IOP Conf. Series. Materials Sci. and Eng., 330(1), 012107. IOP Publishing. https://doi.org/10.1088/1757-899X/330/1/012107
15. Bergant, Z., Savin, A., Grum, J. (2018) Effects of manufacturing technology on static, multi-frequency dynamic mechanical analysis and fracture energy of cross-ply and quasi-isotropic carbon/epoxy laminates. Polymers and Polymer Composites, 26(5-6), 358-370. https://doi.org/10.1177/0967391118798266
16. Technical Information. Sigrafil® continuous carbon fiber tow. Wiesbaden, SGL Group August 2022.

---

Suggested Citation

A. Savin, R. Steigmann, M.D. Stanciu, C.I. Moraras, G. Dobrescu (2024) Evaluation of the mechanical characteristics of CFRP composites and modeling of the delamination phenomenon. The Paton Welding J., 12, 30-34.

---