The Paton Welding Journal, 2012, №07



2012 №07 (02)

2012 №07 (04)

---

The Paton Welding Journal, 2012, #7, 10-15 pages  

STRUCTURE AND WEAR RESISTANCE OF CHROME-MANGANESE DEPOSITED METAL

V.L. MALINOV and L.S. MALINOV

E.O. Paton Electric Welding Institute, NASU, Kiev, Ukraine
 
 
Abstract
Presented are the results of investigations into structure and wear resistance of low-carbon metal of different structural classes, deposited with flux-cored strips and containing approximately 13 % chromium and different amounts of manganese (from 2 to 12 %). The possibility of increasing wear resistance of the deposited metal by tempering and case hardening after hardfacing was studied. It is shown that achieving the optimal amount of meta-stable austenite, along with martensite, in structure of the deposited metal improves its wear resistance.
 
 
Keywords: arc hardfacing, chrome-manganese deposited metal, structure, martensite, meta-stable austenite, tempering, case hardening, wear resistance
 
 
Received:                23.01.12
Published:               28.07.12
 
 
References
1. Ryabtsev, I.A. (2004) Hardfacing of machine parts and mechanisms. Kiev: Ekotekhnologiya.
2. Malinov, L.S., Chejlyakh, A.P. (1981) Chrome-manganese steels of transition grade. Izvestiya Vuzov. Chyorn. Metallurgiya, 4, 101-103.
3. Malinov, L.S., Chejlyakh, A.P. (1983) Effect of manganese and heat treatment on structure and properties of steels Fe-0,1 % C-14 % Cr. Ibid., 6, 83-87.
4. Malinov, L.S., Malinov, V.L. (2009) Resource-saving sparsely alloyed alloys and hardening technologies providing the effect of self-hardening. Mariupol: Renata.
5. Malinov, V.L. (2011) Effect of manganese on structure and wear resistance of deposited metal of the low-carbon steel type. The Paton Welding J., 8, 12-16.
6. Tylkin, M.A. (1965) Strength and wear resistance of metallurgical equipment parts. Moscow: Metallurgiya.
7. Popov, V.S., Brykov, I.N. (1996) Wear resistance of steels and alloys. Zaporozhie: IPK Zaporozhie.
8. Malinov, L.S., Konop-Lyashko, V.I. (1982) Effect of ageing on development of martensitic transformation in deformation of meta-stable austenitic steels. Izvestiya AN SSSR. Metally, 3, 130-133.
9. Gladky, P.V., Kondratiev, I.A., Yumatova, V.I. et al. (1991) Hardfacing flux-cored strips and wires: Refer. Book. Kiev: Tekhnika.
10. Malinov, V.L. Charge of flux-cored strip. Pat. 94862 Ukraine. Int. Cl. C2 B23K 35/28. Fil. 07.06.2010. Publ. 11.06.2011.
11. Malinov, L.S., Malinov, V.L. Method of hardening. Pat. 63462 Ukraine. Int. Cl. C 21 D1/2. Fil. 22.04.2003. Publ. 15.01.2004.
12. Pikalov, S.V. (2009) About possibilities of repair of automobile parts by gas-shielded surfacing with subsequent case hardening. In: Proc. of 1st Int. Sci.-Techn. Conf. on Current Automobile Materials and Technologies, 216-223. Kursk: STU.
13. Malinov, L.S., Chejlyakh, A.P., Malinova, E.L. (1991) Effect of case hardening and subsequent heat treatment on structure, phase composition and abrasive wear resistance of Fe-Cr-Mn steels. Izvestiya AN SSSR. Metally, 1, 120-123.

---

Suggested Citation

V.L. MALINOV and L.S. MALINOV (2012) STRUCTURE AND WEAR RESISTANCE OF CHROME-MANGANESE DEPOSITED METAL. The Paton Welding J., 07, 10-15.

---