The Paton Welding Journal, 2019, №08



2019 №08 (01)

DOI of Article 10.15407/tpwj2019.08.02

2019 №08 (03)

---

The Paton Welding Journal, 2019, #8, 7-11 pages
 
Journal The Paton Welding Journal
Publisher International Association «Welding»
ISSN 0957-798X (print)
Issue #8, 2019 (September)
Pages 7-11

Structure and properties of wear-resistant materials based on Co–Mo–Cr–Si–B alloying system

A.M. Kostin and V.A. Martynenko

Admiral Makarov National University of Shipbuilding 9 Heroiv Ukrainy Prosp., 54000, Mykolaiv, Ukraine. E-mail: volodymyr.martynenko@nuos.edu.ua

The aim of the work was to study the structure and properties of Co–Mo–Cr–Si–B alloying system for the case of its application as a wear-resistant material for hardening the contact surfaces of blades of ship gas turbine engines. The studies were performed with application of the methods of high-temperature differential thermal analysis, electron microscopy, X-Ray micro and X-Ray structural analyses. Hardness and microhardness of phase components were measured, adhesion activity of experimental alloys was investigated using the sessile drop method. It is shown that experimental compositions have a balanced structure based on solid solution of cobalt alloyed with molybdenum and chromium, with hardening by complex silicides, borides and carbides, have acceptable mechanical properties and melting temperature below the temperature of irreversible softening of high-temperature nickel alloys, and are characterized by high adhesive activity, which creates favourable prerequisites for their use in ship gas turbine construction. 10 Ref., 1 Table, 4 Figures.
Keywords: high-temperature nickel alloys, wear-resistant materials, structure phase composition, hardness, melting temperature, adhesive activity

 
Received: 04.06.19
Published: 24.09.19
 
 

References

1. Farafonov, D.P., Migunov, V.P., Alyoshina, R.Sh. (2016) Study of tribological characteristics of materials used for strengthening of flange platforms of GTE blades. Aviats. Mater. and Technol., S1(43), 24-30 [in Russian]. https://doi.org/10.18577/2071-9140-2016-0-S1-24-30
2. Kostin, A.M., Martynenko, V.A., Maly, A.B. et al. (2017) Adhesion-active high-temperature wear-resistant surfacing consumables KMKh and KMKhS. The Paton Welding J., 1, 58-61. https://doi.org/10.15407/tpwj2017.01.11
3. Altukhov, A.A., Gavrilov, O.V. (2004) Application of hightemperature material KBNKhL-2 for surfacing of gas turbine parts. Svarshchik, 2, 22-23 [in Russian].
4. Farafonov, D.P., Bazyleva, O.A., Rogalev, A.M. (2016) Alloys for strengthening of flange platforms of GTE blades. Trudy VIAM, 9(45), 53-60 [in Russian].
5. Pejtchev, G.I., Zamkovoj, V.E., Andrejchenko, N.V. (2009) Comparative characteristics of wear-resistant alloys for strengthening of flange platforms of gas turbine engine blades. Vestnik Dvigatelestroyeniya, 2, 123-125 [in Russian].
6. Som, A.I., Ishchenko, V.Yu., Maly, A.B. (2004) Plasma-powder surfacing with stellite of pipe clamps. Svarshchik, 2, 18-19 [in Russian].
7. Kostin, A.M., Martynenko, V.A., Butenko, A.Yu. (2014) Comparative high-temperature wear-resistance of alloy ChS88UVI and stellite Kh30N50Yu5T2. Zbirnyk Nauk. Prats NUK, 454(4), 55-59. Mykolaiv [in Russian]. https://doi.org/10.15589/jnn20140407
8. Dmitrieva, G.P. et al. (2015) Structure and properties of wear-resistant alloy based on cobalt with niobium carbide. Metallofizika i Novejshie Tekhnologii. 37(7), 973-986 [in Russian]. https://doi.org/10.15407/mfint.37.07.0973
9. Cherepova, T.S. et al. (2014) Wear-resistant alloy for protection of contact surfaces of aircraft engine blades from oxidation at high temperatures. Nauka ta Innovatsii, 10(4), 22-31 [in Ukrainian]. https://doi.org/10.15407/scin10.04.022
10. Yao, M.X., Wu, J.B.C., Liu, R. (2005) Microstructural characteristics and corrosion resistance in molten Zn-Al bath of Co-Mo-Cr-Si alloys. Mater. Sci. & Engin. A, 407, 299-305. https://doi.org/10.1016/j.msea.2005.07.054

---