Automatic Welding, 2016, №02



2016 №02 (02)

DOI of Article 10.15407/as2016.02.03

2016 №02 (04)

---

Avtomaticheskaya Svarka (Automatic Welding), #2, 2016, pp. 19-27

Research progress of supersonic laser deposition technology

Jianhua Yao¹ and V. Kovalenko²

¹Research Center of Laser Processing Technology and Engineering, Zhejiang University of Technology, Hangzhou, China
²Zhejiang Provincial Collaborative Innovation Center of High-end Laser Manufacturing Equipment, Hangzhou, China
³Laser Technology Research Institute, NTUU «Kiev Polytechnic Institute», Kiev, Ukraine
 
 
Abstract
Supersonic laser deposition is a new coating and fabrication process, in which a supersonic powder stream generated in cold spray impinges onto a substrate which is simultaneously irradiated with a laser. It will be increasingly employed for depositing coatings and metal additive manufacturing because of its unique advantages: solid-state deposition of dense, homogeneous and pore-free coatings onto a range of substrate, high build rate at reduced operating costs without the use of expensive gas heating and large volumes of helium, and opening up a new opportunity for efficiently depositing high hardness metallic powders which are usually difficult to be deposited solely by cold spray. Based on the current research results in our group, this paper systematically reviews state-of-the-art of supersonic laser deposition technique at home and abroad, from the viewpoints of materials selection, process optimization, properties characterization, equipment design and so on. The existing issues in these aspects are deeply analyzed, and the corresponding solutions are tentatively proposed. Meanwhile, the potential industrial applications of supersonic laser deposition in various fields are elaborated in detail, as well as the future perspectives and challenges facing this technology, in order to provide insight for further investigations and innovation in supersonic laser deposition as an emerging combination additive re-manufacturing technology with high efficiency, low cost and high quality. 16 Ref., 18 Figures.
 
Keywords: supersonic laser deposition, materials, process parameters, performances, application
 
 
Received:                23.01.16
Published:               12.04.16
 
 
References
 

1. Bray, M., Cockburn, A., O'Neill, W. (2011) The laser-assisted cold spray process and deposit characterization. Surface and Coating Techn., 203, 2851–2857. https://doi.org/10.1016/j.surfcoat.2009.02.135
2. Lupoi, R., Sparkes, M., Cockburn, A. et al. (2011) High speed titanium coating by supersonic laser deposition. Materials Letter, 65, 3205–3207. https://doi.org/10.1016/j.matlet.2011.07.014
3. Jones, M., Cockburn, A., Lupoi, R. et al. (2014) Solid-state manufacturing of tungsten deposits onto molybdenum substrates with supersonic laser deposition. Ibid., 134, 295–297. https://doi.org/10.1016/j.matlet.2014.07.091
4. Olakanmi, E.O., Doyoyo, M. (2014) Laser assisted cold-spray corrosion- and wear-resistant coatings: A review. Thermal Spray Techn., 23, 765–785. https://doi.org/10.1007/s11666-014-0098-x
5. Kulmala, M., Vuoristo, P. (2008) Influence of process conditions in laser-assisted low pressure cold spraying. Surface and Coatings Techn., 202, 4503–4508. https://doi.org/10.1016/j.surfcoat.2008.04.034
6. Li, B., Yang, L.J., Li, Z.H. et al. (2015) Beneficial effects of synchronous laser irradiation on the characteristics of cold-sprayed copper coatings. Thermal Spray Techn., 24, 836–847. https://doi.org/10.1007/s11666-015-0246-y
7. Luo, F., Cockburn, A., Lupoi, R. et al. (2012) Performance comparison of Stellite 6 deposited on steel using supersonic laser deposition and laser cladding. Surface and Coatings Techn., 212, 119–127. https://doi.org/10.1016/j.surfcoat.2012.09.031
8. Yao, J.H., Yang, L.J., Li, B. et al. (2015) Beneficial effects of laser irradiation on the deposition process of diamond/Ni60 composite coating with cold spray. Surface Sci., 330, 300–308. https://doi.org/10.1016/j.apsusc.2015.01.029
9. Li, B., Yao, J.H., Zhang, Q.L. et al. (2015) Microstructure and tribological performance of tungsten carbide reinforced stainless steel composite coatings by supersonic laser deposition. Surface and Coatings Techn., 275, 58–68. https://doi.org/10.1016/j.surfcoat.2015.05.040
10. Yao, J.H., Yang, L.J., Li, B. et al. (2015) Characteristics of performance of hard Ni60 alloy coating produced with supersonic laser deposition technique. Materials and Design, 83, 26–35. https://doi.org/10.1016/j.matdes.2015.05.087
11. Olakanmi, E.O., Tlotleng, M., Meacock, C. et al. (2013) Deposition mechanism and microstructure of laser-assisted cold-sprayed (LACS) Al–12 wt.% Si coatings: Effect of laser power. JOM, 65, 776–783. https://doi.org/10.1007/s11837-013-0611-6
12. Riveiro, A., Lusquinos, F., Comesana, R. et al. (2007) Supersonic laser spray of aluminum alloy on a ceramic substrate. Surface Sci., 254, 926–929. https://doi.org/10.1016/j.apsusc.2007.07.201
13. Yuan, L.J., Luo, F., Yao, J.H. (2013) Deposition behavior at different substrate temperatures by using supersonic laser deposition. Iron and Steel Res. Int., 20, 87–93. https://doi.org/10.1016/S1006-706X(13)60182-X
14. Tlotleng, M., Akinlabi, E., Shukla, M. et al. (2015) Microstructural and mechanical evaluation of laser-assisted cold sprayed bio-ceramic coatings: Potential use for biomedical applications. Thermal Spray Techn., 24, 423–435. https://doi.org/10.1007/s11666-014-0199-6
15. Luo, F., Cockburn, A., Cai, D.B. et al. (2015) Simulation analysis of Stellite 6 particle impact on steel substrate in supersonic laser deposition process. Ibid., 24, 378–393. https://doi.org/10.1007/s11666-014-0176-0
16. Yang, L.J., Li, B., Yao, J.H. et al. (2015) Effects of diamond size on the deposition characteristics and tribological behavior of diamond/Ni60 composite coating prepared by supersonic laser deposition. Diamond and Related Materials (in press). https://doi.org/10.1016/j.diamond.2015.06.014