The Paton Welding Journal, 2015, №09



2015 №09 (06)

DOI of Article 10.15407/tpwj2015.09.07

2015 №09 (08)

---

The Paton Welding Journal, 2015, #9, 45-49 pages
 

Autovacuum brazing in repair of copper panels of mccb moulds

G.M. Grigorenko, A.L. Puzrin, M.G. Atroshenko, M.A. Poleshchuk, A.V. Shevtsov And I.A. Mossokovskaya

E.O. Paton Electric Welding Institute, NASU. 11 Bozhenko Str., 03680, Kiev, Ukraine. E-mail: office@paton.kiev.ua
 
 
Abstract
Using models the possibility of repair of worn-out flat panels of machines of continuous casting of billets (MCCB) moulds by autovacuum brazing of restoration copper layer was tested. The brazed joint was produced between two copper plates without defects in the form of pores and cracks. The tensile strength of copper brazed joint for separation between layers was investigated, and also the bend tests were performed. Thermal resistance of the brazed joint was evaluated. The obtained results allow the method of autovacuum brazing to be recommended for repair of flat panels of the moulds. 12 Ref., 6 Figures.
 
Keywords: MCCB moulds, restoration repair, autovacuum brazing, seams, metallography, mechanical properties, thermal resistance
 
 
Received:                16.06.15
Published:               26.10.15
 
 
References

1. Evteev, D.P., Kolybalov, I.N. (1984) Continuous casting of steel. Moscow: Metallurgiya.
2. Markushin, A.A., Kuklev, A.V., Ajzin, Yu.M. et al. (2005) Radial slab mold with slot channels and nickel coating of walls, 38-41. Moscow: Metallurg.
3. Abramovich, V.R. (1988) Fusion welding of copper and alloys on its base. Moscow: Mashinostroenie.
4. Nikityuk, Yu.N., Grigorenko, G.M., Zelenin, V.I. et al. (2013) Technology of reconditioning repair of slab molds of MCCB with friction stir welding method. Sovr. Elektrometallurgiya, 3, 51-55.
5. Puzrin, L.G., Bojko, G.A., Atroshenko, M.G. (1975) Autovacuum brazing. Kiev: Znanie.
6. Puzrin, L.G., Atroshenko, M.G., Peshcherin, I.G. et al. (1984) Autovacuum brazing of ultra-thick wall vessels of up to hundred tons mass. In: Problems of welding and special electrometallurgy, 76-77. Kiev: PWI.
7. GOST 17325-79: Soldering and tinning. Main terms.
8. (1975) Reference book on soldering. Ed. by S.N. Lotsmanov at al. Moscow: Mashinostroenie.
9. Yong, H. (1979) Basic formulae and data on heat exchange for engineers. Moscow: Atomizdat.
10. Mardyan, M.G., Ryabchikov, E.A., Epshtejn, G.N. (1979) Procedure for determination of cohesive strength of bimetal layers. Zavod. Laboratoriya, 8, 757-759.
11. Keloglu, Yu.P., Zakharievich, K.M., Kartashevskaya, M.A. (1977) Metals and alloys: Refer. Book.
12. Masato, T. (2009) Molds of machines of continuous steel casting of Mashima Kosan. In: Proc. of Int. Sci.-Pract. Seminar on Electrocladding and Thermal Spraying (Ekaterinburg, 2009), 1-19.

---

Suggested Citation

G.M. Grigorenko, A.L. Puzrin, M.G. Atroshenko, M.A. Poleshchuk, A.V. Shevtsov And I.A. Mossokovskaya (2015) Autovacuum brazing in repair of copper panels of mccb moulds. The Paton Welding J., 09, 45-49.

---