The Paton Welding Journal, 2014, №10



2014 №10 (06)

DOI of Article 10.15407/tpwj2014.10.07

2014 №10 (08)

---

The Paton Welding Journal, 2014, #10, 35-37 pages  

ESTIMATION OF POSSIBILITY FOR PRODUCING FULL-STRENGTH JOINT OF LARGE STEEL PARTS USING THE METHOD OF AUTOVACUUM BRAZING OF THREADED PROFILE

M.A. POLESHCHUK, M.G. ATROSHENKO, A.L. PUZRIN and V.L. SHEVTSOV

E.O. Paton Electric Welding Institute, NASU. 11 Bozhenko Str., 03680, Kiev, Ukraine. E-mail: office@paton.kiev.ua
 
 
Abstract
Mechanical properties of brazed threaded joints from similar and dissimilar steels produced by autovacuum brazing method are studied in thread transverse direction. It is determined that tearing strength limit in brazing of low-alloy structural steels corresponds to yield strength of steel after traditional heat treatment. The tearing strength of brazed threaded joints of 12Kh18N10T to 40Kh steels significantly exceeds the yield strength of stainless steel. Permanent joints, produced by means of thread with further autovacuum brazing, can be recommended for manufacture of parts of critical designation. 11 Ref., 1 Table, 3 Figures.
 
 
Keywords: autovacuum brazing, threaded joints, dissimilar steels, mechanical properties
 
 
Received:                02.04.14
Published:               28.10.14
 
 
References
1. Khorunov, V.F. (2008) Principles of brazing of thin-wall structures of high alloy steels. Kiev: Naukova Dumka.
2. (1975) Reference book on brazing. Ed. by S.N. Lotsmonov. Moscow: Mashinostroenie.
3. Serebryanik, I.P. (2011) Autovacuum noncapillary structural brazing. Kiev: Alfa Reklama.
4. Kuznetsov, V.A. (2004) Determination of pressure gas value in brazing with reinforced gap filling by molten brazing filler alloy. In: Proc. of Seminar on State-of-the-Art and Prospects of Development of Brazing. Moscow: Znanie.
5. Karabanov, V.V., Bokharov, I.O. (2012) Solution of problems of leakproofness and reliability of casing pipes. Neft. Khozyajstvo, 1, 42-45.
6. Muraviov, V.I., Mariin, B.N., Chernyshov, L.V. Method of brazing of thin-wall pipes in telescopic joining. Pat. 2193477 RF. Int. Cl. 23K 1/00. Publ. 27.11.2002.
7. Paton, B.E., Medovar, B.I., Puzrin, L.G. et al. (1968) About solution of air gases in solid metal during spontaneous cleaning of its surface. Doklady AN SSSR, 181(1), 70.
8. Puzrin, L.G., Bojko, G.A., Atroshenko, M.G. (1975) Autovacuum brazing. Kiev: Znanie.
9. Grigorenko, G.M., Puzrin, A.L., Atroshenko, M.G. et al. (2012) Influence of high-temperature heating on properties of steels in brazing of composite bodies of high pressure blind flange. Sovr. Elektrometallurgiya, 2, 45-50.
10. GOST 8 479-70: Forged pieces of structural carbon and alloy steel. Introd. 01.01.71.
11. Brooker, H.R., Beatson, E.V. (1957) Industrial brazing. Moscow: Oborongiz.

---