1. Видавничий дім

Видавничий дім "Патон", №Kostin

kostin v.a.

Всього статей опубліковано в журналі«The Paton Welding Journal»: 58

  1. Petrov S.V., Saakov A.G., Taranova T.G., Grigorenko G.M., Kostin V.A. Plasma hardening of surfaces of wheelset ridges 18 (2000, №03)
  2. Borisova A.L., Tunik A.Yu., Grigorenko G.M., Kostin V.A., Astakhov E.A. High-temperature tribological properties of thermal spray coatings containing solid lubricants 31 (2000, №11)
  3. Maksymova S.V., Khorunov V.F., Shonin V.A., Zvolinsky I.V., Voronov V.V., Kostin V.A. Vacuum brazing of dispersion-strengthened copper alloy Glidcop AI-25 ... 13 (2002, №10)
  4. Grigorenko G.M., Grabin V.F., Golovko V.V., Kostin V.A., Alekseenko I.I., Kapitanchuk L.M. Procedure of determination of sizes of ultradispersed non-metallic inclusions in metal of low-alloy steel welds ... 26 (2003, №04)
  5. Grabin V.F., Golovko V.V., Solomijchuk T.G., Goncharenko E.I., Kostin V.A. Analysis of structural state of weld metal produced by using welding wires of the ferritic-pearlitic grade. 17 (2003, №08)
  6. Grigorenko G.M., Golovko V.V., Grabin V.F., Kostin V.A. Effect of metallurgical characteristics of flux on structure, phase composition of high-strength weld metal. 7 (2004, №03)
  7. Grigorenko G.M., Kostin V.A., Golovko V.V., Grabin V.F. Effect of chemical inhomogeneity on the formation of acicular ferrite in high-strength weld metal. 2 (2004, №04)
  8. Grabin V.F., Golovko V.V., Kostin V.A., Alekseenko I.I. Morphological peculiarities of microstructure of weld metal from low-alloy steels with ultralow content of carbon ....15 (2004, №07)
  9. Ryabtsev I.A., Kuskov Yu.M., Ryabtsev I.I.,Novikova D.P., Grigorenko S.G., Kostin V.A. Secondary hardening of deposited metal of the type of dispersion-hardening steel of Fe-C-Ni-Cr-Si-Al-Cu alloying system 4 (2004, №10)
  10. G.M. Grigorenko, V.V. Golovko, V.A. Kostin, V.F. Grabin Effect of microstructural factors on sensitivity of welds with ultra-low carbon content to brittle fracture (2005, №02)
  11. Labur T.M., Ishchenko A.Ya., Taranova T.G., Kostin V.A., Grigorenko G.M. Nature, features of microdeformation in the zone of crack initiation, propagation in high-strength aluminuim alloy D16AT 2 (2005, №10)
  12. Labur T.M., Ishchenko A.Ya., Taranova T.G., Kostin V.A., Grigorenko G.M. Features of crack initiation, propagation under the conditions of off-center tension of 1441 AlДLi alloy welded joints 6 (2005, №11)
  13. T.M. Labur, T.G. Taranova, V.A. Kostin, A.Ya. Ishchenko, G.M. Grigorenko, V.E. Fedorchuk Influence of structural transformations in welding of aluminium alloy B96 on fracture resistance parameters (2006, №11)
  14. L.M. Lobanov, N.A. Pashchin, V.P. Loginov, T.G. Taranova, V.A. Kostin, A.A. Chajka Influence of electrodynamic treatment on the features of fracture micromechanism of welded joints on aluminuim alloy AMg6 (2007, №02)
  15. T.M. Labur, T.G. Taranova, V.A. Kostin, A.Ya. Ishchenko, G.M. Grigorenko, A.A. Chajka Nature of fracture of B96 alloy depending on heating conditions in welding (2007, №02)
  16. T.M. Labur, A.Ya. Ishchenko, T.G. Taranova, V.A. Kostin, G.M. Grigorenko, A.A. Chajka Influence of thermophysical conditions of welding on fracture resistance of the haz metal in the joints of aluminium alloy V96tss (2007, №04)
  17. T.M. Labur, A.A. Grinyuk, T.G. Taranova, V.A. Kostin, A.G. Poklyatsky Features of micromechanism of fracture in joints of aluminium-lithium alloys produced by plasma welding (2007, №09)
  18. T.M. Labur, A.Ya. Ishchenko, T.G. Taranova, V.A. Kostin, G.M. Grigorenko Investigation of the fracture mode of welded joints of high-strength alloy v96tss under the conditions of off-center tension (2007, №11)
  19. G.M. Grigorenko, V.A. Kostin, V.Yu. Orlovsky Current capabilities of simulation of austenite transformations in low-alloyed steel welds (2008, №03)
  20. T.M. Labur, T.G. Taranova, G.M. Grigorenko, V.A. Kostin Influence of thermal conditions of welding on the features of crack initiation in the haz of joints of aluminium alloys V96 and V96tss (2009, №04)
  21. I.I. Ryabtsev, I.A. Kondratiev, V.A. Kostin, D.P. Novikova, I.L. Bogajchuk, A.A. Babinets Structure of phosphorus-containing deposited metal of the tool steel type (2009, №04)
  22. E.G. Ternovoj, V.F. Shulym, A.R. Bulatsev, T.G. Solomijchuk, V.A. Kostin Properties, structure of circumferential joints of tubes made by orbital electron beam welding (2011, №01)
  23. T.M. Labur, V.A. Shonin, T.G. Taranova, V.A. Kostin, V.S. Mashin, I.N. Klochkov Fracture surface morphology at fatigue of MIG-welded joints of AMg6 alloy (2011, №03)
  24. V.V. Golovko, V.A. Kostin, G.M. Grigorenko Peculiarities of the influence of complex alloying on structure formation, mechanical properties of welds on low-alloyed high-strength steels (2011, №07)
  25. V.A. Kostin, V.V. Golovko, G.M. Grigorenko methods for assessment of strengthening of HSLA steel weld metal (2011, №10)
  26. G.K. Kharchenko, A.I. Ustinov, Yu.V. Falchenko, L.V. Petrushinets, S.G. Grigorenko, V.A. Kostin, V.P. Gurienko Vacuum diffusion welding of g-tial intermetallic alloy to 12Kh18N10T steel (2012, №04)
  27. V.A. Kostin Mathematical formulation of carbon equivalent as a criterion for evaluation of steel weldability (2012, №08)
  28. V.A. Kostin, G.M. Grigorenko, V.D. Poznyakov, S.L. Zhdanov, T.G. Solomijchuk, T.A. Zuber, A.A. Maksimenko Influence of welding thermal cycle on structure, properties of microalloyed structural steels (2012, №12)
  29. V.A. Kostin, G.M. Grigorenko, T.G. Solomijchuk, V.V. Zhukov, T.A. Zuber Microstructure of haz metal of joints of high-strength structural steel Weldox 1300 (2013, №03)
  30. A.A. Rybakov, T.N. Filipchuk, V.A. Kostin, V.V. Zhukov Influence of chemical composition of microalloyed steel, cooling rate of haz metal of pipe welded joints on its structure, impact toughness (2013, №09)
  31. V.D. Poznyakov, V.A. Kostin, A.A. Gajvoronsky, I.A. Mossokovskaya, V.V. Zhukov, A.V. Klapatyuk Effect of welding thermal cycle on structure-phase transformations, properties of haz metal of alloyed 30Kh2N2MF type medium-carbon steel (2015, №02)
  32. A.A. Rybakov, T.N. Filipchuk, V.A. Kostin Peculiarities of microstructure, impact toughness of metal of welded joints of pipes of high-strength steel with niobium, molybdenum (2015, №04)
  33. G.M. Grigorenko, V.D. Poznyakov, T.A. Zuber, V.A. Kostin Peculiarities of formation of structure in welded joints of microalloyed structural steel S460M (2017, №10)
  34. V.A. Kostin, G.M. Grigorenko Modelling of temperature fields, stresses, deformations in cylinder shells produced by additive manufacturing method (2019, №07)
  35. O.V. Makhnenko, V.A. Kostin, V.V. Zhukov, E.S. Kostenevich Effect of cooling cycle of welding on structure-phase composition of 15Kh2NMFA steel (2019, №09)
  36. V.D. Poznyakov, O.A. Gaivoronskyi, V.A. Kostin, O.M. Berdnikova, S.V. Shmygelskyi Influence of thermal cycle of surfacing on mechanical properties, resistance of haz metal of rail steel M76 to brittle fracture (2019, №12)
  37. O.M. Berdnikova, V.A. Kostin, V.D. Poznyakov, O.A. Gaivoronskii, T.O. Alekseenko, I.I. Alekseenko Structure and crack resistance of special steels with 0.25−0.31 % carbon under the conditions of simulation of thermal cycles of welding (2020, №05)
  38. A.V. Zavdoveev, V.D. Poznyakov, M. Rogante, S.L. Zhdanov, V.A. Kostin, T.G. Solomiychuk Features of structure formation and properties of joints of s460m steel made by pulsed-arc welding (2020, №06)
  39. V.V. Holovko, D.Yu. Yermolenko, S.M. Stepanyuk, V.V. Zhukov, V.A. Kostin Influence of introduction of refractory particles into welding pool on structure and properties of weld metal (2020, №08)
  40. R.S. Hubatyuk, S.V. Rymar, O.S. Prokofiev, V.A. Kostin, O.V. Didkovskyi, O.F. Muzhychenko Simulation of electromagnetic and thermal fields in the process of induction heating on small specimens with the presence of welded joint of high-strength railway rails (2021, №01)
  41. M.D. Rabkina, V.A. Kostin, T.G. Solomiichuk Peculiarities of emergency failure of a process pipeline (2021, №03)
  42. V.A. Kostin, V.V. Zhukov, O.M. Berdnikova, V.V. Holovko, O.S. Kushnaryova Effect of modification of weld metal of high-strength low-alloy steels on their structure and properties (2021, №05)
  43. R.S. Hubatyuk, S.V. Rymar, O.S. Prokofiev, V.A. Kostin, O.V. Didkovskyi, E.V. Antipin Modeling of the process of induction heat treatment of welded joints from rail high-strength steels (2021, №09)
  44. N.V. Piskun, E.L. Vrzhyzhevskyi, V.A. Kostin, T.G. Taranova, I.L. Bogaichuk, I.I. Statkevych Influence of time of existence of molten pool in electron beam processes on the level of evaporation of elements with a high vapor tension (2022, №01)
  45. O.A. Gaivoronskyi, V.D. Poznyakov, Yu.V. Demchenko, A.M. Denysenko, A.V. Zavdoveev, V.A. Kostin, T.G. Solomiychuk Influence of pulsed-arc welding modes on the structure and mechanical properties of welds and haz metal of welded joints of 30Kh2N2MDF steel (2022, №05)
  46. S.V. Akhonin, V.Yu. Bilous, V.A. Kostin, S.G. Hrygorenko, O.L. Puzrin, E.L. Vrzhyzhevskyi Influence of heat treatment on improvement of mechanical properties of welded joints of sparsely-doped titanium alloy Ti–2.8Al–5.1Mo–4.9Fe (2022, №12)
  47. V.A. Kostin, Yu.V. Falchenko, A.L. Puzrin, A.O. Makhnenko Production, properties and prospects of application of modern magnesium alloys (2023, №04)
  48. V.V. Holovko, O.O. Shtofel, V.A. Kostin Fractal evaluation of grain boundaries branching in the structure of weld metal of low-alloy steels (2023, №06)
  49. Yu.V. Falchenko, L.V. Petrushynets, V.Ie. Fedorchuk, V.A. Kostin, O.L. Puzrin Diffusion welding of magnesium alloy MA2-1 through a zinc interlayer (2023, №09)
  50. V.A. Zaitsev, Yu.V. Kostetskyi, G.O. Polishko, V.A. Kostin, V.P. Petrenko, E.O. Pedchenko Investigations of the quality of metal of high-manganese steel alloyed by aluminium and chromium after electroslag remelting (2023, №12)
  51. S.Yu. Maksymov, G.V. Fadeeva, Jia Chuanbao, V.A. Kostin, A.A. Radzievskaya, D.V. Vasilyev Influence of cooling rate on microstructure and phase composition of HAZ of duplex (DSS) 2205 STEEL in wet underwater welding (2024, №01)
  52. M.A. Khokhlov, O.O. Makhnenko, V.A. Kostin, A.G. Pokliatskyi, Iu.V. Falchenko, Yu.A. Khokhlova Thermo-mechanical processes in friction stir welding of magnesium alloy sheets (2024, №05)
  53. M.P. Reminnyi, V.A. Kostin, V.V. Zhukov Modification and microalloying of the metal of welds on HSLA steels produced by fusion welding method (Review) (2025, №01)
  54. A.Yu. Severyn, V.Yu. Bilous, L.M. Radchenko, V.A. Kostin, I.I. Alekseenko, L.T. Yeremeyeva, M.M. Kuzmenko Study of the temperatures of phase transformation in heat-resistant titanium alloy of Ti‒Al‒Zr‒Si‒Mo‒Nb‒Sn alloying system (2025, №03)
  55. V.M. Korzhyk, D.V. Strohonov, O.S. Tereshchenko, O.V. Ganushchak, A.Yu. Tunik, V.A. Kostin, S.L. Chygileichyk, V.K. Yuliuhin Spherical titanium powder production for 3D printing by plasma-arc atomization of wire materials (2025, №05)
  56. V.V. Holovko, V.A. Kostin, V.V. Zhukov Dispersed oxides influence on the kinetics of the weld metal structural transformations (2025, №06)
  57. V.V. Zhukov, V.A. Kostin, S.G. Hrygorenko, R.S. Gubatyuk Modern approaches to obtaining continuous cooling transformation diagrams for welding (Review) (2025, №10)
  58. S.V. Akhonin, A.Yu. Severyn, V.O. Berezos, V.A. Kostin, I.I. Alekseenko, O.V. Samofalov, V.V. Pashynskyi Investigation of the structural and phase composition of the titanium alloy Ti‒36Nb‒6Al‒1.8Mo‒1.8Zr (2026, №02)
Науково-практичні семінари:
«3D ДРУК МЕТАЛЕВИХ ВИРОБІВ»
(26 травня 2026 р.)
та «НЕРУЙНІВНИЙ КОНТРОЛЬ ТА МОНІТОРИНГ ТЕХНІЧНОГО СТАНУ»
(27 травня 2026 р.)
2026.03.05
НОВІ КНИГИ
2026.01.03 Доступні для завантаження пдф-файли статей «The Paton Welding Journal» за 2024 рік!
2025.12.05
We are pleased to announce that on 5 December 2025, Scopus accepted our application for indexing “The Paton Welding Journal”. Importantly, this decision includes indexing articles published between 2022 and 2025. We sincerely congratulate us all on this joint achievement and encourage Authors to submit new manuscripts.
2025.12.05
Збірка тез пленарних та стендових доповідей конференції Зварювання та споріднені технології для відновлення України
2025.06.02
Зб. тез доповідей наук.-техн. семінарів: 3D друк металевих виробів. Неруйнівний контроль та моніторинг технічного стану
Пропонуємо оформити передплату на видання ІЕЗ ім. Є.О. Патона на 2026 рік.
2023.12.15 Збірка тез доповідей конференції “Сучасні напрями розвитку адитивних технологій”

Найсвіжіші номери журналів на сайті

 Автоматичне зварювання #03 (2026), The Paton Welding Journal #04 (2026), Сучасна електрометалургія #02 (2026), Технічна діагностика та неруйнівний контроль #01 (2026),